Description
PHILIPS SmartBright Solar Floodlight VVP080 Series
A die-cast aluminium solar floodlight for sites that have no power supply and no intention of trenching one in. 1,200 to 4,800 lm, three colour temperatures on the supplied remote, a built-in PIR sensor and a 5 m plug-in cable to a separate monocrystalline panel. No mains connection, no electrician, no running cost.
Product gallery
One platform, four lumen packs — the body, glass lens and 5 m cable are common to all versions

Die-cast aluminium body, tempered glass lens, cool grey finish

5 m plug-in connector on the luminaire end; PIR built into the body

PIR mode holds 5 % and lifts to 100 % on movement

No mains connection, no trenching, no electricity bill
Why a solar floodlight earns its place
The four situations where running a cable is the expensive part
The cost of an outdoor light is rarely the light. It is the trench, the conduit, the consumer unit alteration and the qualified electrician — for a gate post 40 m from the building, that is several times the price of the fitting. VVP080 removes the whole line item: the panel charges a LiFePO4 pack in the body, the body switches itself on at dusk, and the installation is four screws into a wall.
Off grid by design
Monocrystalline panel, PWM charge controller and LiFePO4 battery inside the luminaire. Nothing connects to the mains, so there is no circuit to certify and no bill to pay.
Die-cast aluminium, IK06
Tempered glass over the LEDs and a die-cast body rated IK06 against a 1 J impact — the specification that matters on a site where a strimmer or a ladder will find it.
Three CCTs on one remote
3000 K, 4000 K and 6500 K from the same SKU. Stock one order code and match the warm courtyard or the cool car park on site, without a second pallet.
Type-C top-up
An openable battery box and a USB Type-C input mean a pack that has gone flat over a closed season can be brought back without dismantling the fitting.
Four outputs on one platform
Body, lens, sensor and control are common — only output, panel and battery change
Every version runs at 160 lm/W at 6500 K, so the four SKUs are a straight line rather than four different designs. Pick by the area you have to light, not by the wattage: the panel and battery scale with the lumen pack, which is what keeps the 2–3 hour full-output runtime constant across the range.
Battery energy scales with the pack, not with the price
Technical specifications
All four order codes, side by side — common values merged across columns
| Parameter | LED12 | LED24 | LED36 | LED48 |
|---|---|---|---|---|
| Optical | ||||
| Lumen output @ 6500 K | 1,200 lm | 2,400 lm | 3,600 lm | 4,800 lm |
| LED output power | 7.5 W | 15 W | 22.5 W | 30 W |
| Luminous efficacy @ 6500 K | ≥160 lm/W | |||
| Colour temperature | 3000 K / 4000 K / 6500 K, selectable by remote — 4000 K default | |||
| Colour rendering | CRI≥80, SDCM≤5 | |||
| Light source | LED module behind tempered glass — not field replaceable | |||
| Electrical & solar | ||||
| Battery type | LiFePO4, built into the luminaire, openable battery box | |||
| Battery capacity | 3.2 V 6 Ah | 6.4 V 6 Ah | 9.6 V 6 Ah | 12.8 V 6 Ah |
| Stored energy | 19.2 Wh | 38.4 Wh | 57.6 Wh | 76.8 Wh |
| Solar panel | 8 Wp / 5 V | 15 Wp / 9 V | 23 Wp / 14 V | 30 Wp / 18 V |
| Panel cell type | Monocrystalline | |||
| Charge controller | PWM, charge and discharge protected | |||
| Cycle life | 1,000 charge / discharge cycles | |||
| Charging | Solar, plus USB Type-C input for top-up in low-sun periods | |||
| Sensor & control | ||||
| Sensor | PIR, built into the luminaire — 100 % on motion, 0 % or 5 % when clear, 30 s hold | |||
| Control | Infrared remote control supplied with every pack | |||
| Battery indicator | LED bar showing charge and discharge state | |||
| Mechanical | ||||
| Housing | Die-cast aluminium, cool grey | |||
| Lens | Tempered glass | |||
| Ingress protection | IP66 | |||
| Impact protection | IK06 (1 J) | |||
| Luminaire dimensions | 176 × 175 × 67 mm | 176 × 175 × 67 mm | 226 × 224 × 67 mm | 276 × 279 × 67 mm |
| Panel dimensions | 228 × 216 × 17 mm | 320 × 230 × 17 mm | 390 × 300 × 17 mm | 430 × 390 × 17 mm |
| Cable | 5 m plug-in connector, luminaire end | |||
| Mounting | Wall or surface bracket, screws supplied — not for pole mounting | |||
| Operating temperature | 0 °C to 50 °C (charging stops below 0 °C) | |||
| Warranty | 2 years as standard, 3 and 5 year options available | |||
Mounting, panel placement and the 5 m cable
No wiring, but the panel position decides whether the light works in January
The luminaire fixes to a wall or flat surface on the supplied bracket with four screws. The panel is a separate assembly on its own frame, connected by a 5 m plug-in cable — no cutting, no terminal block, no polarity decision at the fitting.
- Panel first. Site the panel where it sees the midday sun for most of the year — clear of tree canopy, walls and the building overhang. A shaded panel is the single most common reason a solar light underperforms.
- Then the light. The PIR sits in the luminaire body, so aim the body at the area to be detected, not just at the surface to be lit.
- Keep the cable run short and uncoiled. 5 m is supplied; coiling the surplus against the wall is fine, running it in a tight loop around metal is not.
- Dusk to dawn, automatic. Once activated the light charges from sunrise to sunset with the LEDs off, then discharges after dark. If another light shines on the panel at night the lamp will stay off — that is the control working, not a fault.
Internal dimensions differ between the lumen packs — 176 × 175 mm on LED12 and LED24, 226 × 224 mm on LED36 and 276 × 279 mm on LED48 — so check the bracket footprint before specifying a recess.
Dimensional drawing — bracket, wall plate and panel fixing spacing for all four lumen packs (mm)
In the box
One carton, one SKU, everything needed to commission
Each set packs the luminaire, the separate solar panel, the 5 m plug-in cable, the infrared remote control and the mounting screws into a single printed carton. There is no separate panel order code and no accessory to forget, which is what makes the range practical for distribution: MOQ 52 pcs with MPQ 4 pcs on the 1,200–3,600 lm sizes, and MOQ 51 pcs with MPQ 3 pcs on the 4,800 lm.
The carton also prints the equivalent conventional floodlight rating alongside the LED output — the 4,800 lm version is marked 480 W. That is the conventional lamp it replaces, not the power it draws: the LED input is 30 W on that size and 7.5 to 30 W across the range.
Where it is specified
Public facilities, courtyards, landscape and parking — general outdoor use
Residential and courtyard
Driveways, side returns, garden walls and pool surrounds. The 3000 K setting keeps a residential scheme warm; PIR at 5 % gives a low guide light between visits.
Commercial and industrial
Gatehouses, loading areas, yard perimeters and staff car parks on sites where the mains stops at the fence line. IK06 and IP66 suit wash-down and open exposure.
Public and landscape
Park entrances, footpaths, signage and municipal car parks. No supply means no excavation permit and no cable to repair after groundworks.
Security retrofit
Adding a motion-triggered light to a wall that has no circuit: the PIR holds 100 % on movement and drops to 0 % or 5 % after 30 seconds.
Landscape and courtyard use — the panel is the only part that needs direct sun
VVP080 or BVC010 — how to choose
Two solar floodlight families in the same catalogue, different jobs
| Parameter | VVP080 (this range) | BVC010 |
|---|---|---|
| Output range | 1,200 – 4,800 lm, 4 SKUs | 600 – 6,000 lm, 7 SKUs |
| CRI | ≥80 | ≥70 |
| Efficacy | ≥160 lm/W | ≥165 lm/W |
| Housing and impact | Die-cast aluminium, IK06 | See BVC010 series page |
| Warranty | 2 years (3 and 5 year options) | 1 year |
The honest trade-off: BVC010 reaches 6,000 lm and runs about 5 lm/W higher, while VVP080 spends that efficiency on CRI 80 and a die-cast aluminium body that survives a knock. For colour-critical facades, hospitality courtyards and hard-wearing sites, take VVP080. For the highest lumens per pound on a sheltered wall, take BVC010 — see the BVC010 series.
Complete product lineup
Four order codes — the 2, 3 and 5 year warranty versions are separate 12NCs on the same luminaire
| 12NC | Description | Power | L × W × H | Output |
|---|---|---|---|---|
| 911401854203 | VVP080 LED12/MCCT Solar | 7.5 W | 176 × 175 × 67 mm | 1,200 lm |
| 911401854303 | VVP080 LED24/MCCT Solar | 15 W | 176 × 175 × 67 mm | 2,400 lm |
| 911401854403 | VVP080 LED36/MCCT Solar | 22.5 W | 226 × 224 × 67 mm | 3,600 lm |
| 911401854503 | VVP080 LED48/MCCT Solar | 30 W | 276 × 279 × 67 mm | 4,800 lm |
Warranty options — 2 year, 3 year and 5 year ordering codes
Every lumen pack can be ordered under three warranty terms. The luminaire, panel, battery and carton are identical; only the warranty length and the order code differ. Customers who need a 3-year warranty or a 5-year warranty for a tender should order the matching code below rather than specifying a second product.
| Warranty | LED12 · 1200 lm | LED24 · 2400 lm | LED36 · 3600 lm | LED48 · 4800 lm |
|---|---|---|---|---|
| 2 year (standard) | 911401854203 | 911401854303 | 911401854403 | 911401854503 |
| 3 year | 911401854603 | 911401854703 | 911401854803 | 911401854903 |
| 5 year | 911401855003 | 911401855103 | 911401855203 | 911401855303 |
Also from the PHILIPS lighting range
Solar and mains-powered outdoor luminaires that share the same mounting and installation logic
Frequently asked questions
Sizing, runtime and installation questions we get on solar floodlights
Does the VVP080 need mains wiring or an electrician?
How long does it stay on after a full charge?
Can I change the colour temperature on site?
What happens in winter or in a run of cloudy days?
Can it be mounted on a pole?
Is a 3 year or 5 year warranty version available?












